亚洲欧洲精品国产二码,亚洲国产一成人久久精品,中文字幕无码av激情不卡久久,成人精品国产亚洲AV蜜芽

首頁 > Service > Q&A

Analysis of five common faults of Suzhou First radium laser marking machine

日期:2020-07-29    點擊數:

Suzhou first laser marking machine common five kinds of failure analysis laser marking machine problems, if not solved in time will affect the delivery time of products, although the laser marking machine maintenance is more troublesome, but its principle is relatively simple, there are many problems can be solved by themselves without professional and technical personnel maintenance, the following is laser marking Five common faults of standard machine

1. The marking pattern of laser marking machine is not clear

Solution: check whether the thickness of the die plate is uniform, whether the molding pressure is too small, whether the temperature is too low, whether the machine accuracy is reduced.

Process control points: die plate thickness error should be controlled within 0.o01mm, hardness should be maintained in 230-280n / mm. Because the hologram is to mold interference fringes by applying a certain amount of pressure to the mold roller, if the hardness of the die plate is not enough, the internal stress will make the die plate deformed or damaged in the process of imprinting.

2. The marking pattern of laser marking machine is dim

Solution: check whether the heating temperature is too low and whether the molding pressure drops.

Key points of process control: the setting of molding pressure should comprehensively consider the molding temperature, the type of holographic material or the softening point of coating layer, etc. If the pressure is too high, the die plate is easy to be damaged or the holographic material will be crushed; if the pressure is too low, the molding image is not clear and incomplete; for the circular pressing mode, the initial pressure of the pressure rollers on both sides is generally about 0.08mpa; after the molding starts, gradually increase the pressure of the pressure roller to 030 ~ 0.50mpa. The molding speed can be adjusted according to the quality of the press and the performance of the machine.

3. The marking pattern of laser marking machine turns white

Solution: check whether the molding speed is too slow and whether the molding temperature is too high.

4. Marking film of laser marking machine

Causes: the hot pressing temperature is higher than the degradation temperature, the coating viscosity will increase, which will cause the sticky plate and make the film wound on the holographic imprint roller.

Solution: reduce the hot pressing temperature.

5. The marking pattern of laser marking machine is clear and fuzzy

Causes: the temperature distribution of hot pressing device is not uniform or the die plate is not smooth.

立即咨詢0512-50179464

掃一掃,加關注

江蘇總部:江蘇省昆山市巴城鎮東定路600號

華南制造基地:東莞市寮步鎮仁居路1號松湖智谷研發中心一區2棟6樓

Copyright ? 蘇州首鐳激光科技有限公司 版權所有     ICP備案號:蘇ICP備14056626號-1     技術支持:微企云通
象州县| 灵宝市| 沂源县| 丹东市| 罗江县| 广州市| 区。| 雅江县| 晋宁县| 南郑县| 张掖市| 万宁市| 宜丰县| 湘潭县| 吉安市| 台东市| 鲁山县| 元氏县| 景宁| 特克斯县| 孝义市| 电白县| 南宫市| 长泰县| 寿宁县| 沅陵县| 临湘市| 寿宁县| 寿宁县| 牙克石市| 穆棱市| 龙胜| 大姚县| 贡山| 甘肃省| 邛崃市| 长沙市| 昂仁县| 乌兰察布市| 灌阳县| 绍兴县|